Optical fiber free essay sample

A type of inside cable designed for horizontal use in non-plenum areas. While horizontal cable must be fire retardant, the National Electrical Code (NEC) specifications are not as demanding as those governing the use of plenum cable or riser cable. See also NEC, plenum, plenum cable, and riser cable. 2. Backbone Cable : Backbone cabling is the inter-building and intra-building cable connections in structured cabling between entrance facilities, equipment rooms and telecommunications closets. Backbone cabling consists of the transmission media, main and intermediate cross-connects and terminations at these locations. This system is mostly used in data centers. 3. Patch Cords: a short cord with a plug at each end, or a plug at one end and a pair of clips at the other, used for temporarily connecting two pieces of equipment or signal paths. 4. Connectors: A device for holding two parts of an electrical conductor in contact. 5. Conduit: A tube or duct for enclosing electric wires or cable. 6. Racks: A computer rack (commonly called a rack) is a metal frame used to hold various hardware devices such as servers, hard disk drives, modems and other electronic equipment. Some may refer to a rack as LAN or network furniture as resembles a shelving structure where components can be attached vertically, stacked on top of one another. A computer rack can also be called a relay rack or open rack. 7. Punch-Down Blocks: is a type of electrical connection often used in telephony. It is named because the solid copper wires are punched down into short open-ended slots which are a type of insulation-displacement connectors. These slots, usually cut crosswise (not lengthwise) across an insulating plastic bar, contain two sharp metal blades which cut through the wires insulation as it is punched down. These blades hold the wire in position and make the electrical contact with the wire as well. 8. Consolidation Points: an optional device for interconnecting horizontal cables between the Horizontal Cross-Connect and the Telecommunications Outlet or MUTOA within a structured cabling system. 9. Crimpers: A tool used to crimp, to join two pieces of metal 10. Fish Tape : a flat tempered spring-steel tape or wire used in pulling electric wire and cables (as into conduit runs) —called also snake wire 11. Continuity Tester: is an item of electrical test equipment used to determine if an electrical path can be established between two points;[1] that is if an electrical circuit can be made. The circuit under test is completely de-energized prior to connecting the apparatus 12. Category 5e/6 Cable : cabling is used as a cabling infrastructure for 10BASE-T (Ethernet), full duplex 100BASE-TX (Fast Ethernet) and 1000BASE-T (Gigabit Ethernet, or GbE) networks. The Cat 5e standard provides performance of up to 100 MHz and can be used up to a maximum length of 100 meters. 13. Binder Groups: A group of wire pairs bound together, usually by some sort of color-coded plastic tape or thread. In a large twisted pair cable, there may be many pairs combined into binder groups of 25 pairs for ease of connectivity management. Each pair within a binder group is uniquely color-coded for further ease of management. See also cable and wire. 14. Hybrid/Composite Cable : composite cable A communications cable having both optical and metallic signal-carrying components. Note 1: A cable having optical fiber(s) and a metallic component, e. g. , a metallic twisted pair, used solely for conduction of electric power to repeaters, does qualify as a composite cable. Note 2: A cable having optical fiber(s) , plus a metallic strength member or armor, does not qualify as a composite cable. Hybrid †¢An optical communications cable having two or more different types of optical fibers, e. g. , single-mode and multimode fibers. 15. Pulling Cable : The act of pulling the wires, as of a puppet; hence, secret influence or management, especially in politics; intrigue 6. Wavelengths of Light: The length of a single cycle of a wave, usually measured from crest-to-crest. For electromagnetic waves 17. EMI : is the disruption of operation of an electronic device when it is in the vicinity of an electromagnetic field (EM field) in the radio frequency (RF) spectrum that is caused by another electronic device. 18. Optical-Fiber Strand : Is this referring to the actual p ure glass on the middle of the fiber 19. Index of Refraction : the ratio of the velocity of light in a vacuum to that in a medium. 0. wordnetweb. princeton. edu/perl/webwn 21. Cable Jacket : The outer protective coating which covers the core of the cable.. 22. Cladding Size : A metal coating bonded onto another metal under high pressure and temperature. 23. Multifiber Cables : Fiber optic Cable bearing many fibers independently sheathed and capable of carrying unrelated signals. They often surround a central strength member, and can be either loose- or tight-buffered. One standard configuration is a 12-fiber cable. 24. Differential Mode Delay: 25. In an optical fiber, the variation in propagation delay that occurs because of the different group velocities of different modes. Synonym multimode group delay. 26. Chromatic Dispersion : In optics, dispersion is the phenomenon in which the phase velocity of a wave depends on its frequency,[1] or alternatively when the group velocity depends on the frequency. Media having such a property are termed dispersive media. Dispersion is sometimes called chromatic dispersion to emphasize its wavelength-dependent nature, or group-velocity dispersion (GVD) to emphasize the role of the group velocity